I did an oil change. Thought the car took 4.4 quarts but it only takes 3.7 quarts. I poured in slightly under 4 quarts. The engine is a 1.5 in-line turbo (Honda Civic Si). It’s reading past the fill line slightly. How bad is it? Do I need to pour some out? What am I risking? What symptoms should I be looking for?

    • minibyte@sh.itjust.works
      link
      fedilink
      arrow-up
      25
      ·
      edit-2
      4 months ago

      Close enough!

      Edit for a recommendation to OP: if you plan to change the oil in the same car for the foreseeable future – get a transparent plastic pitcher and add a fill line mark for the oil on the outside with nail polish, in your case 3.7 quarts. I do this with my car and makes for a no brainier oil change.

  • RightHandOfIkaros@lemmy.world
    link
    fedilink
    English
    arrow-up
    41
    ·
    edit-2
    4 months ago

    Automechanic for 10 years here.

    No. A little over the max fill line on the dipstick isnt going to hurt it. 1/8 of an inch overfilled or less is okay.

    Usually if you don’t prefill the oil filter and only add what they say then sometimes it can be a little under. Its not a big deal.

    Way too much and you risk damaging piston rings or flooding, but you really have to fill it to the point its spilling from the dipstick tube.

    • waz@lemmy.world
      link
      fedilink
      arrow-up
      6
      ·
      4 months ago

      Having once upon a time overfilled my oil by almost a quart, I think you are mostly right.

      Engine oil should stay in the crankcase. During normal operation, some of it is pumped elsewhere to lubricate the crankshaft, cams, and other mechanical components. The rest of the oil sloshes and splashes around the crankcase keeping everything slippery. If there is too much excess in the crankcase, components moving can push the oil somewhere it shouldn’t be.

      In my case, when turning left, the excess oil was pushed passed the piston rings and burned in a huge cloud of blue smoke. It wasn’t a proud moment, but stopping in a random service station and having Bruce try to drain a quart of oil out of the engine, because I couldn’t afford a full oil change was awkward.

      … Anyway: all of that to say this:

      If you have too little, your oil pressure light will probably come on. If you have too much, you’ll notice it somewhere else.

      • RightHandOfIkaros@lemmy.world
        link
        fedilink
        English
        arrow-up
        3
        ·
        edit-2
        4 months ago

        If you find yourself overfilling often, or if you are in the business and do heavy line work like I did (engine/transmission replacements and overhauls), just save yourself the time and get a fluid evacuator. If you overfill something you can pump a bit back out, they make them with pneumatic attachments or with a handpump that looks a bit like a bicycle tire air pump. Shove the little feed tube down the dipstick and pump whatever you need to back out.

        EDIT: Fluid Evacuator

    • BleatingZombie@lemmy.world
      link
      fedilink
      arrow-up
      5
      ·
      edit-2
      4 months ago

      My wife was a mechanic (lube tech) for a year or two when we were first dating. One guy came in after TOPPING OFF his oil with WATER and was complaining that it wasn’t running right

      • RightHandOfIkaros@lemmy.world
        link
        fedilink
        English
        arrow-up
        3
        ·
        4 months ago

        Its pretty unusual to have lube techs doing any diagnosis, but did she ask him if he likes chocolate milkshakes? Because That’s exactly what you create when you mix water in engine oil. Just don’t drink it.

      • RightHandOfIkaros@lemmy.world
        link
        fedilink
        English
        arrow-up
        13
        ·
        4 months ago

        I mean, you don’t HAVE to. But you can pour some oil into the filter to pre-fill it so the oil doesn’t have to pump so long for the air you cycle out of the system, but the amount of time that happens for is so small it basically doesn’t matter. If the oil filter is easy to access and faces upward (the solid part faces the floor and open part faces up) then I would do it, but I wouldn’t do it in any other circumstance just to not have oil spilling and making a mess everywhere.

        Youre not going to blow up the engine if you don’t. But it gives some people better peace of mind.

      • yeehaw@lemmy.ca
        link
        fedilink
        arrow-up
        1
        ·
        edit-2
        4 months ago

        I just don’t pil change, it might show a little high, then you run the motor to cycle it through the system then it levels out. Good enough. A little less or extra doesn’t hurt anything.

        Source: not a mechanic, but I know a lot of them and I’ve never taken my personal vehicle in for a change in 25 years.

  • Pat_Riot@lemmy.today
    link
    fedilink
    arrow-up
    12
    ·
    4 months ago

    If you had got it changed by a professional, they would have simply poured in all four quarts. You didn’t hurt a thing.

  • AlwaysTheir@lemmy.one
    link
    fedilink
    English
    arrow-up
    8
    ·
    4 months ago

    Not pro knowl just knuckle dragging mechanic advice: run the car for a bit. Rev it up. Turn it off. Pull the dip stick. If there is no foaming you’re fine.

  • AngryCommieKender@lemmy.world
    link
    fedilink
    arrow-up
    7
    ·
    4 months ago

    At least you didn’t grab a case of oil because it was on sale for $10 for 12 quarts only to realize that instead of grabbing 10w 35, I had grabbed 20w 50. Took 16 oil changes to use all that oil.

  • bluGill@kbin.run
    link
    fedilink
    arrow-up
    6
    ·
    4 months ago

    The danger is the crankshaft will hit the oil and foam up. Start the engine run at some rpm for a minute then check for foam at the dipstick if okay do a test drive with sharp corners and check again - if no foam you are okay. If ther is foam drain some out and then let the engine / foam settle overnight before driving.

    • remotelove@lemmy.ca
      link
      fedilink
      arrow-up
      2
      arrow-down
      1
      ·
      4 months ago

      This is the way.

      (I’ll just note that oil with bubbles in it does not look like an actual milkshake. If it looks like a milkshake, then bad things are happening.)

  • SonicBlue03@sh.itjust.works
    link
    fedilink
    English
    arrow-up
    5
    ·
    4 months ago

    I wouldn’t think it would be a problem. If you’re concerned you can siphon some out through the dipstick opening.

  • GladiusB@lemmy.world
    link
    fedilink
    arrow-up
    3
    ·
    4 months ago

    You will be ok. Over filling will not do anything other than make seals break easier. Oil circulates throughout the block all the time. A tiny bit more or short will not effect any long term performance.

    I have worked on cars my whole life and I am a logistics manager for a fleet of commercial vehicles.

  • Nougat@fedia.io
    link
    fedilink
    arrow-up
    3
    ·
    4 months ago

    I wouldn’t worry about it. Even on brand new cars, there are plenty where losing (burning) a quart of oil between changes is “within specifications.” The engine is likely going to burn a little bit of oil just because, and you’ll be lower again soon enough.

  • Maeve@kbin.earth
    link
    fedilink
    arrow-up
    2
    arrow-down
    1
    ·
    4 months ago

    It’s better to run s little too little, (neither is great)I doubt that much extra one time matters, but Ianam. A lot too much will kill it.